Component Matching of Industrial Gas Turbines

An important first step in understanding the gas turbine design process is the knowledge of how individual components act given their particular boundary conditions. However, in order to effectively leverage these individual design processes, a basic knowledge of how these components interact with each other is essential to the overall performance of a gas turbine unit. The power and efficiency outputs of a gas turbine are the result of a complex interaction between different turbomachines and a combustion system. Therefore, performance metrics for a gas turbine are not only based on the respective performances of each turbine, compressor, and combustion system, but also on their interactions. The concept of component matching becomes crucial in understanding how to deal with these systems simultaneously.

two-shaft-gas-turbine
Figure 2 – Simplified Two-Shaft Gas Turbine Arrangement Modeled in AxCYCLE

In general, gas turbines for industrial applications consist of a compressor, a power turbine, and a gas generator turbine designed into one of two arrangements. The first arrangement invokes the use of the gas generator turbine to drive the air compressor, and a power turbine to load the generator on a separate shaft. This two-shaft arrangement allows the speed of the gas generator turbine to only depend on the load applied to the engine. On a single-shaft arrangement, the system obviously cannot exist at varied speeds and the power turbine coupled with the gas generator turbine would be responsible for driving both the generator and the compressor. A simplified diagram of each arrangement is displayed in Figures 1 and 2.

Read More

Heat Recovery Steam Generator Design

Heat recovery steam generators (HRSGs) are used in power generation to recover heat from hot flue gases (500-600 °C), usually originating from a gas turbine or diesel engine. The HRSG consists of the same heat transfer surfaces as other boilers, except for the furnace. Since no fuel is combusted in a HRSG, the HRSG have convention based evaporator surfaces, where water evaporates into steam. A HRSG can have a horizontal or vertical layout, depending on the available space. When designing a HRSG, the following issues should be considered:

hrsg-boiler
Figure 1: Schematic of a HRSG boiler
  • The pinch-point of the evaporator and the approach temperature of the economizer
  • The pressure drop of the flue gas side of the boiler
  • Optimization of the heating surfaces

The pinch-point (the smallest temperature difference between the two streams in a system of heat exchangers) is found in the evaporator, and is usually 6-10 °C, which can be seen in Figure 2. To maximize the steam power of the boiler, the pinch-point must be chosen as small as possible. The approach temperature is the temperature difference of the input temperature in the evaporator and the output of the economizer. This is often 0-5 °C.

Read More

The Significance of Quantifying Uncertainties in Turbomachinery CFD

The increased use of CFD for turbomachinery design is an outcome of the increasing accuracy thanks to high computational resources. Although the benefits of such computations are strong, the approximations and errors derived from CFD could significantly affect the prediction of crucial parameters such as flow temperature and heat transfer. This article will present the challenges related to uncertainties in turbomachinery CFD, based on “Uncertainty Quantification in Computational Fluid Dynamics and Aircraft Engines” [1]

The exact definition of boundary conditions presents one of the biggest challenges in CFD and turbomachinery given the high accuracy needed to determine the distributions of the non-uniform conditions to which turbomachinery components are subjected [2].

Read More

The Economic Optimization of Renewable Energy

clean-blog-postGlobal warming is a very popular topic at the present time. With the upwards trend of clean technology and the realization that strict climate policy should be implemented, demand of renewable energy has sky-rocketed while conservative plant popularity continues to fall. Additionally, the number of coal power plants have significantly dropped since its peak era, as they are now known as the largest pollutant contribution, producing nitrogen, sulfur oxide and carbon dioxides.

Renewable energy comes from many sources: hydropower, wind power, geothermal energy, bioenergy and many more. The ability to replenish and have no limit on usage and application makes renewable energy implementation attractive. To make this even better, it also produces low emission. Theoretically, with the usage of renewable energy, human-kind should be able to meet their energy needs with minimal environmental damage. With growth rates ranging from 10% to 60% annually, renewable energy is getting cheaper through the technological improvements as well as market competition. In the end, the main goal is to maximize profit while minimizing our carbon footprint.  Since the technology is relatively new, capital costs are still considerably higher compared to more traditional (–and naturally harmful) implementations. This begs the question of exactly how we maximize the economic potential of a renewable energy power generation plant.

Read More

Multi-Dimensional Coupling CFD Method for Shrouded Turbines

Tip leakage is generated inevitably by the clearance between the rotating blades and the stationary casing of a turbine, and is responsible for both the aerodynamic losses in a turbine stage and the high heat-loads in the tip region [2]. To decrease tip leakage and improve component performance, shroud seal structures have been widely applied to modern turbine components, especially to low pressure turbines, because of their advantage on both aerodynamic and structural features. However, due to the complexity of the shroud geometry, the flow structures and thermodynamic process in shroud can be extremely complicated, that is interactions of vortices, separations, jet flow, etc. Thus, because of the complex geometry of shrouds, as well as strong interactions between the tip leakage and main flow, it is not easy to draw a numerical simulation with satisfactory accuracy and time-costing in shrouded turbines. This begs the question of what should the compromise be between using simplified loss models and full 3D CFD analysis for leakage modelling?

In the main flow path of a turbine the flow will always be dominated by the blades shape, while for leakage cases the flow will be dominated by the motion and evolution of small eddies. Rosic et al. [1] reviewed the importance of shroud leakage modelling in multistage turbines. The comparison of measurements and 3D calculations shows that the flow in shrouded low aspect ratio turbines is dominated by shroud leakage. This is especially true as regards the loss distribution. The rotor shroud leakage flow greatly increases the secondary flow in the downstream stators and drives low energy fluid towards mid-span. It was pointed out that with very low values of shroud leakage the flow is reasonably well modelled by a simple 1D model of the leakage flow, using sources and sinks on the casing. However, for more representative real clearances, full 3D modelling of the seal and cavity flows is necessary in order to obtain reasonable agreement. Given that developing a simulation method with both high precision and fast solving speed is imperatively demanded for engineers to assess new designs, Zhengping Zou et al. [2] suggested that one of the potential approaches for solving the problem is a method that couples low dimensional models, 1D and 2D models, of the shroud flow with 3D (three-dimensional) simulations of the main flow passage. Specifically, some boundary source and boundary sink is set on the interface between the shroud and the main flow passage, and the source term and sink term are determined by the shroud leakage model. The schematic of this process is given in Fig. 1. The results of his study [2] demonstrate that the proposed models and methods will contribute to pursue deeper understanding and better design methods of shrouded axial turbines.

Read More

Feasibility of Mixed Flow Compressors in Aero Engines

The term, “mixed flow compressor”, refers to a type of compressor that combines axial and radial flow paths. This phenomenon produces a fluid outflow angle somewhere between 0 and 90 degrees with respect to the inlet path.  Referred to as the meridional exit angle, the angled outflow of this mixed flow configuration possesses the advantages of both axial and centrifugal compressors.  Axial compressors can produce higher order efficiencies for gas engines, but they have relatively low-pressure ratios unless compounded into several stages.  Centrifugal compressors can produce high-pressure ratios in a single stage, but they suffer from a drop in efficiency.  The geometrical distinction of mixed flow compressors allows for higher efficiencies while maintaining a limited cross-sectional area.  The trade-off for a mixed flow compressor when introduced to aero gas turbines is that there is an associated weight increase due to the longer impellers needed to cover this diagonal surface.  However, when related to smaller gas turbines, the weight increase becomes less significant to the overall performance of the engine.

Read More

Exchanging Steam for SCO2

In recent days, many people find themselves spending time and resources on uncovering the best solution to optimize the power generation cycle. Until recently, 80% of power plants worldwide (whether fossil fuel, nuclear, or clean technology) used steam as its main working fluid and while it is still the most common option, today’s power plants are finding another fluid to use.

Although supercritical CO2 study began in the 1940’s, it was disregarded as an alternative fluid option because it was expensive to explore and steam was still perfectly reliable at the time. Nowadays due to increasing quantity and quality demand in power, researchers are looking into the possibility of replacing steam with supercritical carbon dioxide. The discover of this property,  increases the incentive of exploring the technology further. This year, the US Department of Energy is awarding up to $80 million towards projects to build and operate a supercritical CO2 plant.

Read More

An Introduction to Cavitation in Hydro Turbomachinery

A major concern for pump system engineers over the last fifty years has been caviation. Cavitation is defined as the formation of vapor bubbles in low pressure regions within a flow. Generally, this phenomenon occurs when the pressure value within the flow-path of the pump becomes lower than the vapor pressure; which is defined as the pressure exerted by a vapor in thermodynamic equilibrium conditions with its liquid at a specified temperature. Normally, this happens when the pressure at the suction of the pump is insufficient, in formulas NPSHa ≤ NPSHr, where the net positive suction head is the difference between the fluid pressure and the vapor pressure at the pump suction and the “a” and “r” stand respectively for the values available in the system and required by the system to avoid cavitation in the pump.

The manifestation of cavitation causes the generation of gas bubbles in zones where the pressure gets below the vapor pressure corresponding to that fluid temperature. When the liquid moves towards the outlet of the pump, the pressure rises and the bubbles implode creating major shock waves and causing vibration and mechanical damage by eroding the metal surfaces. This also causes performance degradation, noise and vibration, which can lead to complete failure. Often a first sign of a problem is vibration, which also has an impact on pump components such as the shaft, bearings and seals.

Read More

Mesh Generation Characteristics for an Accurate Turbomachinery Design

This post will examine the meshing requirements for an accurate analysis of flow characteristics in terms of turbomachinery applications, based on Marco Stelldinger et al study [1]. Computational Fluid Dynamics (CFD) are widely used for the analysis and the design of turbomachinery blade rows.  A well-established method is the application of semi-unstructured meshes, which uses a combination of structured meshes in the radial direction and unstructured meshes in the axial as well as the tangential direction. Stelldinger’s paper presents a library for turbomachinery meshing, which enables the generation of semi-unstructured meshes for turbomachinery blade passages, including cavities, fillets and varying clearance sizes. The focus lies on the generation of a mesh that represents the real geometry as accurately as possible, while the mesh quality is preserved.

The above was achieved by using two different approaches. The first approach divides the blade passage into four parts. Inside of these parts, a structured grid is generated by solving a system of elliptic partial differential equations. The second approach is based on the domain being split into fourteen blocks. It has benefits concerning computational time towards the first one, because of a faster generation procedure as well as a faster performance of the inverse mapping.

Read More

A Look into Combined Cycle Power Plants – Problems, Advantages and Applications.

urs Combined Cycle Power Plants are among the most common type of power generation cycle. Demand of CCP application has risen across board due to the rising energy demand (and consumption) as well as growing environmental awareness. Combined cycle is a matured energy that has been proven to generate much lower CO2 (and other environmental footprints) compared to a traditional fossil fuel steam or gas turbine power generation cycle Consequently, this application is often looked as a “better” substitute compared to other a fossil fuel technologies. That being said, CCP is still a temporary alternative to substitute SPP since although CCP generally is more environmentally friendly, CCP process still requires the combustion of fossil fuel (though at a significantly lower degree compared to SPP) for initial heat/energy source.

The application takes two kinds of thermodynamic cycle in assembly to work together from the same heat source. Fluid Air and fuel enters a gas turbine cycle (Joule or Brayton) to generate electricity, waste heat/energy from working fluid will then be extracted then go through a Heat Recovery Steam Generator and towards steam turbine cycle (Rankine) to generate extra electricity. The main advantage of this cycle combination is the improvement of overall net efficiency (around 50-60% higher compared to each cycle alone), thus, lower fuel expenses. With that being said, net efficiency of a CCP is often inflated especially on systems which use a low-temperature waste heat.

Read More

Page 4 of 1012345678910