A pump is hardware that feeds energy to a fluid (e.g. Water) to flow through channels. Pumps are used, for example, to direct water out of the ground, to transport drinking or sewerage water over large distances in combined pipe networks or to discard water from polders. In any practical application, the pump needs to work with its best performance. It is also important to check that the flow rate and head of the pump are within the required specifications, which are normally presented as the Pump Characteristic curves. These plots play an important role in understanding the region in which the pump needs to be operated thus ensuring the life of the pump.
Pump Characteristic Curves
The performance of any type of pump can be shown graphically, which can be based on either the tests conducted by the manufacturer or the simulations done by the designer. These plots are presented as Pump Characteristic Curves. The hydraulic properties of any pump (e.g. Centrifugal Pump) can be described by the following characteristics.
Net Positive Suction Head (NPSH) Curve
The Q-H curve gives the relation between the volume flow rate and the pressure head, i.e. the lower the pump head, the higher the flow rate. Q-H curves are provided by the manufacturer of the pump and can normally be considered as simple quadratic curves. Read More
The lubrication system is one of the most important systems of an engine.
This system should ensure:
Delivery of the required oil amount to the moving parts (e.g.-Bearings);
Dissipation of the heat generated due to friction by circulation of lubricant throughout the system; and
Cleaning of the oil from contamination and impurities introduced during engine operation.
To meet the above requirements, the lubricant circulation (lubricant reaching each component) should happen at appropriate pressure and mass flow rate throughout the system. This is also required in order to avoid cavitation caused by adverse pressure, and excessive heat generation due to less mass flow rate, at any place or particularly at any component. However, sometimes lubricant does not circulate properly to each corner of the system or to the rotating components. In some cases, the rotation of the crankshaft can actually starve the bearings and increase the internal heat due to insufficient supply of lubrication.
To avoid such problems, simulation engineers must model the whole system at all operating modes. They can predict the best system by varying flow rates (volumetric or mass flow rates), system pressures, temperatures, heat flows, as well as by changing the system geometry itself. Such modelling can be performed easily and with sufficient accuracy in a 1D Thermal Fluid analysis tool, such as AxSTREAM NET™ developed by SoftInWay.
It is worthwhile to use a 1D-Analysis tool in this case, because it can be used at any stage of the system design process to explore more options for improving the final design and to reduce development cycle time. The simulation engineer can easily create a model of automotive engine lubrication system, using different elements (components) which are available in the element database of AxSTREAM NET™. The system configuration can also be easily changed at any stage in the design process without rebuilding the complex 3D models.
Let us try to understand how to build a 1D scheme for an automotive engine lubrication system in a 1D tool (AxSTREAM NET™). First, we need to identify the major elements (components) which are part of the automotive engine lubrication system as per their order or sequence in the scheme. A typical engine lubrication system involves components like Oil – sump, strainer, pump and filter, all of which are parts of the initial oil suction line. In addition, the main gallery involves components like flow passages within the connecting rods, crankshaft, and bearings. The typical connections among these elements are shown in Figure 1.
Now let’s see the arrangement of a few components with their specific purposes towards the construction of the whole model.
It is very important to have Anti-Icing Systems for ground-based gas turbines located in humid climates (where air relative humidity can be more than 80% and dense fog can cause air temperatures to drop below 5 0C). Such climatic conditions lead to ice formation. This ice can plug the inlet filtration system causing a significant drop in pressure in the inlet system, which in turn leads to performance loss. In extreme cases, there is even a possibility that the ice pieces get ingested into the compressor (first blade stage) which may cause foreign object damage. Ice may also cause the disruption of compressor work because of excessive vibration, or surging by decreasing the inlet flow. The major factors that lead to the ice formation in gas turbines are ambient temperature, humidity and droplet size. So, under the climatic conditions which are prone to ice formation, an anti-icing system is employed which heats the inlet air before entering the compressor. Let us discuss some important aspects of Anti-Icing Systems.
The objective of an Anti-Icing System is to prevent or limit the ice formation in the gas turbine inlet path.
Gas Turbine Anti-Icing Systems (GT-AIS) can be categorized in two groups.
Inlet heating systems
Component heating systems
Inlet heating systems operate by transferring heat from a heat source (exhaust gases can be used) to the cold ambient air at the entrance of the gas turbine. If the temperature of inlet air raises sufficiently by this heat transfer, icing cannot form in the gas turbine intake.
AxCYCLE™ is a tool, which provides the flexibility and convenience to study various parameters and understand the performance of thermodynamic cycles.