[:en]The lubrication system is one of the most important systems of an engine.
This system should ensure:
Delivery of the required oil amount to the moving parts (e.g.-Bearings);
Dissipation of the heat generated due to friction by circulation of lubricant throughout the system; and
Cleaning of the oil from contamination and impurities introduced during engine operation.
To meet the above requirements, the lubricant circulation (lubricant reaching each component) should happen at appropriate pressure and mass flow rate throughout the system. This is also required in order to avoid cavitation caused by adverse pressure, and excessive heat generation due to less mass flow rate, at any place or particularly at any component. However, sometimes lubricant does not circulate properly to each corner of the system or to the rotating components. In some cases, the rotation of the crankshaft can actually starve the bearings and increase the internal heat due to insufficient supply of lubrication.
To avoid such problems, simulation engineers must model the whole system at all operating modes. They can predict the best system by varying flow rates (volumetric or mass flow rates), system pressures, temperatures, heat flows, as well as by changing the system geometry itself. Such modelling can be performed easily and with sufficient accuracy in a 1D Thermal Fluid analysis tool, such as AxSTREAM NET™ developed by SoftInWay.
It is worthwhile to use a 1D-Analysis tool in this case, because it can be used at any stage of the system design process to explore more options for improving the final design and to reduce development cycle time. The simulation engineer can easily create a model of automotive engine lubrication system, using different elements (components) which are available in the element database of AxSTREAM NET™. The system configuration can also be easily changed at any stage in the design process without rebuilding the complex 3D models.
Let us try to understand how to build a 1D scheme for an automotive engine lubrication system in a 1D tool (AxSTREAM NET™). First, we need to identify the major elements (components) which are part of the automotive engine lubrication system as per their order or sequence in the scheme. A typical engine lubrication system involves components like Oil – sump, strainer, pump and filter, all of which are parts of the initial oil suction line. In addition, the main gallery involves components like flow passages within the connecting rods, crankshaft, and bearings. The typical connections among these elements are shown in Figure 1.
Now let’s see the arrangement of a few components with their specific purposes towards the construction of the whole model.
We as human kind have always aimed at achieving something better, something bigger. This led to the research on gas turbines, which was mainly inspired due to the immediate requirement in the aerospace and power generation industry, to also look beyond the scope of aeronautics.
Today gas turbine technology is often used when dealing with aerospace and power generation industries, but believe it or not, gas turbine technology has been used in ground transportation too; notably locomotives.
The Early Applications
After the first world war, several countries had the expertise and the finances to invest in achieving the technological edge in the new post war era. The gas turbine technology was one such technological endeavor, and by the mid-20th century the gas turbine could be found in several applications. Birth of gas turbine locomotives can be credited to two distinct characteristics of these locomotives versus the contemporary diesel locomotives. First, there are fewer moving parts in a gas turbine, decreasing the need for lubrication. This can also potentially reduce the maintenance costs. Second, the power-to-weight ratio is much higher for such locomotives which makes a turbine of a given power output physically smaller than an equally powerful piston engine, allowing a locomotive to be powerful enough without being too bulky.
[:en]The concept of using gas turbines to power a car is not new. In fact, for many decades now, various car manufacturers have experimented with the idea of using either axial or radial gas turbines as the main propulsion of concept vehicles. In the 50’s and 60’s it was Fiat and Chrysler who introduced such concept cars. In those cases, the gas turbine was directly powering the wheels for propulsion. Toyota followed the same concept in the 80’s (Figure 1) . Their concept car utilized a radial turbine in order to propel the vehicle using an advanced electronically controlled transmission system. The main advantage of a gas turbine compared with conventional reciprocating (or even rotary) car engines is the fact that it has a much higher power-to-weight ratio. This means that for the same engine weight, a gas turbine is able to deliver much higher power output. This is why aviation was one of the biggest adopters of this technology.
Looking to solve the problem of range anxiety in electric vehicles, many companies have started exploring the business model of recharging electric batteries in automotive vehicles with a parallel turbine engine driving a generator – coined under the term ‘micro-turbine range extender’ (or MTRE). As seen in the turbine-powered car programs initiated in the 50s and 60s, issues with low efficiencies, slow throttle response, and capital cost of the powertrain rendered all of these programs futile shortly after their inception. However, the revolution of electric vehicles and hybrid technologies has allowed this technology to resurface from a different direction. With battery-driven electric motors designated as the main driver, these cars are equipped with a technology that has both energy efficient low-end torque as well as groundbreaking throttle response and many of the former drawbacks during its initial iterations are solved using an electric drivetrain. The turbine-engine, instead of operating as the main driver, will now only operate at its most efficient power output mode and work to simply drive electricity through the generator, recharging the vehicle’s battery packs. Acting as an isolated thermo-mechanical system, a micro-turbine range extender can be designed and optimized without having to worry about the varying duty cycles and idling that is inherent in the vehicle’s drivetrain. The thermodynamic model of a typical micro-turbine range extender can be seen below in Figure 1.
One application within commercial vehicles that has benefitted from this technology utilizes a MTRE system developed by Wrightspeed. The specific application lies within retrofitting refuse trucks with this electric powertrain in order to help them save an estimated $35,000 a year on fuel and maintenance costs. In such heavy-duty applications, it is obvious that the potential for fuel cost and maintenance savings is much higher due to the large fuel burning needed for these vehicles as well as the harsh drive cycle a refuse truck goes through. The question in the expansion of this technology generally comes in two forms: What makes the micro-gas turbine range extender a better alternative than a normal ICE hybrid option? – and – What is the viability of scaling this for consumer vehicles given the capital cost of the drivetrain?
[:en]The concept of turbine-powered automotive vehicles is not necessarily an unfamiliar idea or a technology that has yet to be explored. In fact, several prominent automakers explored this concept as early as the 1950s and 60s – with real, functional prototypes. Notably, Rover-BRM in the UK as well as Chrysler and General Motors in the US employed turbine engine programs to test the viability of such engines in the commercial market. The Chrysler turbine engine program began its research back in the late 1930s and eventually ran a public user program from September 1964 to January 1966 where a total of 55 cars were built. General Motors had tested gas turbine-powered cars with its many iterations of the Firebird in the 50s and 60s. Rover and British Racing Motors developed several prototypes of their Rover-BRM concept that actually participated in the Le Mans race three years in a row, from 1963 through 1965. However, even Chrysler, which was considered the leader of gas turbine research in automobiles, had to eventually abandon their program in 1979 after seven iterations of the turbine engine. Many of the initial issues with heat control and acceleration-lag were improved during the program’s lifetime, but the program had never paid off in the retail automotive sector, and its continued development was deemed too risky for Chrysler at the time.
Several decades later, we are seeing a resurgence of turbine motors in automobiles, but now serving as a range extender generator for electric vehicles instead. As with many upcoming technologies, learning from past research and failed historical attempts can bring light to the most elegant and innovative solutions for today’s modern challenges. This revolution of an old concept shares many of the qualities that made turbine engines attractive back in its initial development phase. Such advantages include the ability to run on any flammable liquid and the high power density that results in a significantly lower weight and size contribution than its piston engine counterpart.
[:en]Familiar to many, the 2011 SuperTruck program was a five-year challenge set by the U.S. Department of Energy to create a Class-8 truck that improves fuel efficiency by 50 percent. Hoping for even more groundbreaking achievements this time around, the Department of Energy has initiated a second five-year program to bring further fuel-efficiency advancements and near closer to eventual commercialization. Cummins, Peterbilt, Daimler Trucks North America, Navistar, and Volvo Group remain the five teams involved in this R&D endeavor. Michael Berube, head of the Energy Department’s vehicle technology office mentioned “SuperTruck II has set goals beyond where the companies think they can be.” SuperTruck II is looking for a 100 percent increase in freight-hauling efficiency and a new engine efficiency standard of 55 percent. With such lofty goals, the SuperTruck II development teams will need to tackle improvements in freight efficiencies from all sides.
Material considerations, body aerodynamics, low-resistance tires, predictive torque management using GPS and terrain information, combustion efficiency, and several other improvements methods on the first iteration have demonstrated how the SuperTruck II will require a multi-phase and integrated systems approach to achieve equally successful numbers. However, with an engine efficiency target that is 31 percent above the SuperTruck’s first go around, special attention will be required on engine advancement to achieve an efficiency standard of 55 percent.
Axial and mixed flow fans have been in high demand for a number of years. The application of these machines span many different industries including HVAC, automotive, appliance, military equipment, and much more. Like many other types of turbomachinery, changing industry standards and market trends have resulted in fierce rivalry to compete on lifespan, efficiency, environmental and user friendliness, and overall quality. With this in mind, it goes without saying that companies are looking for tools needed to develop highly efficient equipment while minimizing noise as quiet fans are typically more desirable which results in higher demand and marketability.
While the term of air conditioning in relation to automotive might instantly correlate to a system which provides passenger with a comfortable air temperature/environment, HVAC systems also are used for heating and cooling of batteries in such application as well as cooling of the vehicle fuel systems. Thermal management for automotive application isn’t easy though. Many factors have to be accounted for in order to build a dependable cooling system.
While talking about HVAC concerns and challenges which arise in automotive application, the biggest inconvenience commonly comes down to the lack of cold air produces. Mobile refrigeration/air conditioning systems come with quite a few concerns from two sides: the refrigeration side, where it removes heat and injects cold air, and from the electrical side which provides control. From the system, the most common challenges are found in moisture –which would fail the cooling system if present in the air, soiled condenser which would block air flow, and various other mechanical complications which might occurs.
[:en]Within the realm of turbocharging, there are a number of different design challenges that influence the design process on both large-scale marine applications and smaller-scale commercial automobile applications. From aerodynamic loads to dynamic control systems to rotor dynamics and bearing challenges, turbochargers represent a special subset of turbomachinery that requires complex and integrated solutions. Turbocharger rotors specifically, have unique characteristics due to the dynamics of having a heavy turbine and compressor wheel located at the overhang ends of the rotor. The majority of turbocharger rotors are supported within a couple floating-ring oil film bearings. In general, these bearings provide the damping necessary to support the high gyroscopic moments of the impeller wheels. However, there are several disadvantages of working with these oil systems that have allowed different technologies to start to surface for these turbomachines. With the floating-ring oil models, varying ring speed ratios and oil viscosity changes significantly influence the performance of the rotor dynamic model.
The application of oil-free bearings have started to emanate due to the overall consistency of their performance and the minimized heat loss associated with air as the damping fluid. Studies on these bearing types for turbomachinery applications are neither trivial nor unique, as they have seen plenty of exposure within the commercial and military aircraft industries within turbo compressors and turboexpanders. However, the success of these specific applications are due to the fact that these turbomachines operate with light loads and relatively low temperatures. The main design challenges with foil air bearings are a result of poor rotor dynamic performance, material capabilities, and inadequate load capacities at high temperature/high load applications.
Increasing regulation for reducing emissions has forced the automotive industry to accept different technologies over the years in order to stay ahead of the market. In an industry that is so accustomed to internal combustion engines, new solutions such as electric motors and turbocharger systems have allowed experts in other industries to cultivate an influence in the automotive market. Specifically in the realm of turbomachinery, increased development has gone into designing turbochargers in order to minimize the effect and size of internal combustion engines. Design challenges are inherent in the fact that an engine is a positive displacement device whereas the turbocharger falls under aerodynamic turbomachinery. The two separate machine types have distinctly different flow characteristics, and the proper sizing of a turbocharger for its parent engine requires proper modeling of the engineering system as a whole.
In general, initial turbocharger sizing becomes a matter of obtaining the necessary boundary conditions required for a preliminary design. A thermodynamic cycle analysis of an ICE-Turbocharger system will allow the designer to obtain an initial idea of the bounds