Typically, supersonic turbine consists of supersonic nozzles with a subsonic inlet and one or two rows of rotating blades. The turbine usually has partial arc admission. The total flow could go through either a single partial arc or several ones. The latter is typical for a steam turbine control stage or standalone applications. The inlet manifold or nozzles chests, as well as exhaust duct, are critical parts of the turbine as well. Due to the very frequent application of partial admission, it is not possible to implement any significant reaction degree. Thus, this kind of turbine is almost always an impulse type. However, some reaction degree could still be applied to full admission turbines. The influence of the rotor blades profile designed for high reaction degree on rotor-stator supersonic interaction and turbine performance is not well studied at the moment.
Several decades later, we are seeing a resurgence of turbine motors in automobiles, but now serving as a range extender generator for electric vehicles instead. As with many upcoming technologies, learning from past research and failed historical attempts can bring light to the most elegant and innovative solutions for today’s modern challenges. This revolution of an old concept shares many of the qualities that made turbine engines attractive back in its initial development phase. Such advantages include the ability to run on any flammable liquid and the high power density that results in a significantly lower weight and size contribution than its piston engine counterpart.
Over the years, as steam turbine technology advanced, the design principles were based on either impulse type or reaction type with reaction type being more efficient. Though impulse was not as efficient as reaction type, it gained popularity due to lower cost and compact size. With advances in design and optimization methods being employed, the efficiency levels between these two types are not very distant, ranging between 2 – 5% based on the size and application. Read More
The potential of supercritical CO2 implementation is vast across power generation applications spanning nuclear, geothermal and even fossil fuel. The cycle envisioned is a non-condensing closed loop Brayton cycle with heat addition and rejection inside the expander to indirectly heat up the carbon dioxide working fluid.
People are pushing turbine inlet temperature to extremes to achieve higher power and efficiency. Material scientists have contributed a lot to developing the most durable material under high temperatures such as special steels, titanium alloys and superalloys. However, turbine inlet temperature can be as high as 1700˚C  and cooling has to be integrated to the system to prolong blade life, secure operation and achieve economic viability.
A high pressure turbine can use up to 30% of the compressor air for cooling, purge, and leakage flows, which is a huge loss for efficiency. It is worth it only if the gain of turbine inlet temperature can outweigh the loss of cooling. This applies to both aviation engines and land based gas turbines.
The history of turbine cooling goes back 50 years and has evolved to fit different environments. The diversity of turbine cooling technology we see today is just the tip of the iceberg. As time goes on and technology advances, people are able to achieve higher cooling efficiency at lower coolant usages. For different goals and needs, different constructs can be applied but the detailed cooling design must balance with the whole system and make the most of technological advances in the areas. For example, if the flow path is optimized, mechanical design is modified, or if new material is employed, the cooling design needs to change accordingly. One thing worth mentioning is that manufacturing of hot section components and turbine cooling design have an interdependent cause and effect, outpacing and leading each other to new levels. Merging of disciplines and additive manufacturing will, in the future, bring more flexibility to turbine cooling design.
- Historically turbomachinery development began with empirical rules postulated by early pioneers. With the need for jet engine for aircraft propulsion, dimensionless analysis became popular, followed by the 1 D mean line design and 2D meridional methods. Today 2D meridional methods with 3D blade to blade CFD/FEA methods are a necessity as efficiency and reliability requirements are further pushed.
- One key aspect of 2D meridional design is S1-S2 optimization, which is a time consuming, laborious task and hence subject to human errors. S1-S2 optimization is a task of reviewing, adjusting and optimizing the flow path in the Tangential (S1 or blade-to-blade or pitchwise) and the Meridional (S2 or span wise) planes. The main purpose is to:
- Fit the flow path to specific meridional dimensional constraints
- Adjust blade-to-blade parameters while taking into account structural constraints.
– Input a set of boundary conditions, geometrical parameters and constraints that are known to the user.
Step 2: Design space generation
– Thousands of machine flow path designs can be generated from scratch
– Explore a set of design solution points using the Design Space Explorer
– Adjusting geometric parameters while retaining the desired boundary conditions is also possible
Historically IE was developed for the design of axial turbines (mainly steam). Later, it was expanded for gas turbines (especially blade cooling calculations) and axial compressors via plug-in modules. The new challenge designers face today is developing mixed flow machinery. An effective system for modern turbomachinery design needs to do the following:
The improvement of the flow path is crucial, and an advanced design can be achieved through several strategies. The aerodynamic optimization of gas and steam turbines can lead to enhanced efficiency. In addition to that, the minimization of secondary losses is possible by introducing advanced endwall shaping and clearance control. Moreover, further increase of efficiency can be achieved by decreasing the losses of kinetic energy at the outlet from the last stage of the turbine. This can be done using longer last-stage blades as well as improving the diffuser recovery and stability.
Material considerations, body aerodynamics, low-resistance tires, predictive torque management using GPS and terrain information, combustion efficiency, and several other improvements methods on the first iteration have demonstrated how the SuperTruck II will require a multi-phase and integrated systems approach to achieve equally successful numbers. However, with an engine efficiency target that is 31 percent above the SuperTruck’s first go around, special attention will be required on engine advancement to achieve an efficiency standard of 55 percent.